The HydroStar
System!
The heart of the HydroStar system
is the hydrogen/oxygen generator since it converts water into these
gases to power your engine. A water tank and pump store and supply
water for the generator. Precise electronic signals from the
HyTronics module initiate and sustain the creation of hydrogen and
oxygen within the generator, An In-Dash Gauge and Indicator Assembly
allows you to accurately monitor all aspects of the HydroStar
System. Every part of the HydroStar System is ruggedly designed, for
long life and reliable operation.
Take a closer look at selected
parts of the system to get a basic understanding of how they work
and interact:
Hydrogen/Oxygen Generator
The Generator contains a coil and
two cylindrical electrodes; used to generate both hydrogen and
oxygen. Each is made from stainless steel and/or ceramic, also very
durable materials. However, two very different atomic forms of
hydrogen are produced within the Generator. Most of the generated
hydrogen is Ortho hydrogen, a very powerful and fast burning gas
created by the two electrodes. A precisely controlled, high
frequency signal from the HyTronics module activates and controls
the electrodes.
The other form of hydrogen, Para
hydrogen, is created by the coil, but in much less quantity than
Ortho hydrogen. A precisely controlled, very low frequency
electronic signal from a separate circuit within the HyTronics
module activates and controls the coil. Para hydrogen is a less
powerful and slower burning gas, but is necessary to prevent
precombustion (commonly called "knocking") within your engine. Para
hydrogen slows the burning rate of the hydrogen mix, thus boosting
its octane level. Such precise control allows you to exactly match
your engine's octane requirements. To raise octane levels in
gasoline, specific additives must be used to slow its burning rate.
At best this is an inaccurate and inefficient method since it
depends upon trying to average the octane requirements for millions
of engines.
Technically speaking, the
Hydrogen/Oxygen Generator itself is an electronic circuit. The two
electrodes form a huge capacitor, thousands of times larger than
capacitors used in typical circuits, with water acting as the
dielectric. The inner electrode is negatively charged and the outer
electrode is positively charged, by the high frequency HyTronics
signal. Chemically, each water molecule is composed of two
positively charged atoms of hydrogen and one negatively charged atom
of oxygen. Since opposite charges attract, the positively charged
hydrogen atoms are pulled towards the inner electrode. This action
aligns every water molecule between the electrodes, with the ends of
each molecule being pulled in opposite directions.
Another electronic circuit is
formed by the Generator coil. This is an inductive circuit, meaning
it creates a magnet field as apposed to a charged field created by
the water capacitor. The very low HyTronics signal (actually a short
pulse) activates the magnetic field of the coil. As soon as the
pulse stops, the magnetic field collapses. This creates an even
stronger magnetic field, but a field of opposite polarity. That is
how an inductive circuit works, an action commonly called "inductive
kick". Each pulse is precisely timed so that almost immediately
after the magnetic field reverses, another short pulse arrives. Once
again the coil is charged and its magnetic field collapses. But now
the continually reversing magnetic field becomes even stronger due
to the added energy of each new pulse. Eventually( actually within a
few seconds) the coil reaches its maximum magnetic strength, called
its saturation point, which is extremely high.
HyTronics Module
The HyTronics Module contains
electronic circuits for controlling and/or providing power to all
the HydroStar System's electrically operated devices. Separate
circuits exist to perform each of the following functions.
-
Provide power to the Generators
electrode in the form of a high frequency signal, creating Ortho
hydrogen and oxygen.
-
Provide power to the Generator
coil in the form of a very low frequency signal, creating Para
hydrogen and oxygen.
-
Control power to the water tank
pump via signals received from the generator water level sensor.
-
Provide busing and terminal
points for distributing power to system gauges, indicators, and
sensors.
To permit easy monitoring of the
HydroStar Systems functions, two gauges: Generator pressure (GEN
PRESS) and engine cylinder head temperature (CHT) and four indicator
lights: GEN WATER LOW, PUMP ON, TANK WATER LOW, and PWR ON. These
are installed into your vehicles dash, or mounted in a nearby
console.
The HydroStar cd ebook manual
is 94 pages long, gives you complete instruction on building,
w/troubleshooting, mostly is pvc pipe, some steel pipe. Shows
the HyTronics Coil Module w/electrodes, creating dual orthohydrogen, parahydrogen
fuel. Includes where to obtain parts, w/phone#s & addresses, some of
them toll free, and also the electronic schematics of operation. IT
also shows mechanics of throttle linkage to carburetor, etc. for
precise adjustment of fuel to be applied into the device your
running.
The full 94 page HydroStar
cd ebook manual/plans
is 10.00 + $5.00 S&H
|
|
|
 |
|
HydroStar Plans CD
|
$10.00 + $5.00 S&H
|
|
If you have any questions
The contents of these pages are subject to change without
notice.
Page created on August 10 2005
No part of OK Hydrogen Concepts may be reproduced in any way, or
by any means, without the prior written permission of OK Hydrogen Concepts.
Use of any index or listing of Software for the purpose of constructing
a mailing list, creating promotional materials or producing a printed
or electronic catalog of any kind is expressly forbidden without the
prior written permission of OK Hydrogen Concepts
© 2005-2005 OK Hydrogen Concepts
All rights reserved.
Other sites of interest.
USANet Creations
Koi Fish Breeders
Website Hosting Directory
|
